5 Minute Forced Entry (FE) Door
The FDI05M Forced Entry Resisting Door System is designed to provide 5 minutes of forced entry protection from a variety of tools.
Features
DOS Codes and Model Numbers
Basic Use: Use this door system to provide protection in those applications where a forced entry threat exists. It is recommended that this door be used in conjunction with protected wall areas.
Limitations: This door has been designed to meet the 5-minute forced entry requirements as set forth in DOS SD-STD-01.01, Rev.G (amended). It is recommended that each end user determine the forced entry threat and choose the correct product to meet and resist that threat.
Construction
Doors and frames are constructed of 11-gauge steel components welded together. Each door will have 11 gauge vertical and horizontal steel stiffeners. Top and bottom of door are flush with face sheets.
Specifications
Door construction: Doors are constructed of steel plates, and steel tubes 1 ½” thick.
Door Frame Construction: Door frame assembly is constructed of steel tubes. Framing dimensions are 2” wide x 5” deep. Door frames are completely fabricated at factory and shipped with doors attached. All doors are pre-tested for all locking functions, clearances, and ease of operation, to ease field installation. All joint connections are welded to provide a rigid assembly when installed. The doorstop is built into the frame. Frames are predrilled to accept ½” anchors 12” on center. Shims are provided to take up a space at each anchor. Wiring diagrams are shipped enclosed in the hardware packages.
Hardware Assembly: Each door is equipped as follows:
Optional Hardware: Refer to the SHW group page for additional hardware information. You must select a lockset, pull handle, or panic device that suits your application. Most hardware is shipped pre-assembled with the door unit.
Subframes: To meet forced entry requirements of DOS SD.STD-01.01 (Rev. G amended), steel tube subframes ¼” wall thickness minimum, must be attached to concrete or masonry with Hilti® Epoxy Anchoring System. An acceptable alternative is the use of steel embeds, ½” thick minimum. These systems are included as options in our product line.
Finish: All doors and frames are furnished prime painted, ready for final finish in field. Options: Factory can apply polyurethane enamel; link to color chart is available on the main page. Doors can also be fitted with various types of architectural metals.
Glazing: Glazing materials shall be of a type approved by H.P. White Laboratory, Inc. for forced-entry resistance. Size to be limited to 20” x 30” vision area. Glazing is replaceable without removing the door from the frame.
Applicable Standard
Weights and Measurements
Standard Door:
Door Thickness: 1 ¾”
Frame Thickness: 2” x 5”
Door Size: 36” x 84”
Frame Size: 40” x 86”
Rough Opening: 40 ½” x 86 ¼”
Shipping Weight: 900 lbs
The FDI05M Forced Entry Resisting Door System is designed to provide 5 minutes of forced entry protection from a variety of tools.
Features
- Provides 5 Minute Forced Entry Protection
- Brookfield i8513 5" x 5.5" needle bearing hinges
- Heavy duty 11-Guage steel construction
- Door and frame shipped as a complete unit
- Single vision, double vision, opaque
DOS Codes and Model Numbers
- w/Vision - DOS 1141 GDT-05N-FDI-01
- Opaque - DOS 2141 GDO-05N-FDI-01
Basic Use: Use this door system to provide protection in those applications where a forced entry threat exists. It is recommended that this door be used in conjunction with protected wall areas.
Limitations: This door has been designed to meet the 5-minute forced entry requirements as set forth in DOS SD-STD-01.01, Rev.G (amended). It is recommended that each end user determine the forced entry threat and choose the correct product to meet and resist that threat.
Construction
Doors and frames are constructed of 11-gauge steel components welded together. Each door will have 11 gauge vertical and horizontal steel stiffeners. Top and bottom of door are flush with face sheets.
Specifications
Door construction: Doors are constructed of steel plates, and steel tubes 1 ½” thick.
Door Frame Construction: Door frame assembly is constructed of steel tubes. Framing dimensions are 2” wide x 5” deep. Door frames are completely fabricated at factory and shipped with doors attached. All doors are pre-tested for all locking functions, clearances, and ease of operation, to ease field installation. All joint connections are welded to provide a rigid assembly when installed. The doorstop is built into the frame. Frames are predrilled to accept ½” anchors 12” on center. Shims are provided to take up a space at each anchor. Wiring diagrams are shipped enclosed in the hardware packages.
Hardware Assembly: Each door is equipped as follows:
- Door Closer (LCN 4041 CUSH)
- (2) Forced Entry Locks (Adams Rite 1850S w/ 15tt Thumbturns)
- (2) Brookfield i8513 5" x 5.5" needle bearing hinges
- Aluminum Threshold (Pemko 177AV36)
- Weather Stripping (Pemko SS88D17)
Optional Hardware: Refer to the SHW group page for additional hardware information. You must select a lockset, pull handle, or panic device that suits your application. Most hardware is shipped pre-assembled with the door unit.
Subframes: To meet forced entry requirements of DOS SD.STD-01.01 (Rev. G amended), steel tube subframes ¼” wall thickness minimum, must be attached to concrete or masonry with Hilti® Epoxy Anchoring System. An acceptable alternative is the use of steel embeds, ½” thick minimum. These systems are included as options in our product line.
Finish: All doors and frames are furnished prime painted, ready for final finish in field. Options: Factory can apply polyurethane enamel; link to color chart is available on the main page. Doors can also be fitted with various types of architectural metals.
Glazing: Glazing materials shall be of a type approved by H.P. White Laboratory, Inc. for forced-entry resistance. Size to be limited to 20” x 30” vision area. Glazing is replaceable without removing the door from the frame.
Applicable Standard
- DOS SD.STD-01.01 (Rev. G amended)
Weights and Measurements
Standard Door:
Door Thickness: 1 ¾”
Frame Thickness: 2” x 5”
Door Size: 36” x 84”
Frame Size: 40” x 86”
Rough Opening: 40 ½” x 86 ¼”
Shipping Weight: 900 lbs